Zappi EV Charger Reviews

About Zappi

The Zappi EV charger is built in Britain by the myenergi company and has all the reliability Australians have come to expect from UK products.

Its stand-out feature is it can solar smart charge and supply an EV with only surplus power from rooftop solar. Unlike some EV chargers that require extensive additional hardware to smart charge, it’s easy and relatively cheap to purchase a Zappi with all the hardware required.

A drawback is the myenergi company doesn’t have an Australian office. Also, an earlier version of the Zappi had some units fail in Australia. Hopefully, myenergi has learned from this and the current version won’t have reliability issues.

Single-Phase Zappi

Homes with single-phase power can only install single-phase EV chargers. According to its datasheet the single-phase version of the Zappi can supply 7kW of power.

3-Phase Zappi

Households with 3-phase power can install single-phase or 3-phase EV chargers. The 3-phase Zappi can provide up to 22kW of power, but few EVs can accept that much. Most can only charge at 11kW or less. For this reason, and because single-phase EV chargers are usually cheaper to buy and install, homeowners with 3-phase power may decide to use a single-phase charger.

Smart Charging

If desired, the Zappi can smart charge an EV using only surplus power from rooftop solar. Because this would normally only receive a low feed-in tariff, it’s usually the cheapest way to charge a car. Exactly how much you’ll save depends on your electricity plan and solar system size and how much you drive, but it can be over several hundred dollars a year per vehicle.  But if there are electricity plans available in your area that offer low daytime rates or special low rates for EV charging, it reduces the financial benefit of solar smart charging.

The Zappi comes with a CT clamp sensor and the Zappi Hub which is a device that lets it connect to the internet and makes smart charging possible. While the older version of the Zappi didn’t require the Hub to smart charge, current ones do. You can save $50 by not getting the Zappi Hub, but that may not be smart as it won’t smart charge without it. So long as you get the Hub and have it all installed correctly, the Zappi is able to smart charge without potentially expensive additional equipment.

You can read about a homeowner’s experience with using an older version of the Zappi for smart charging here.

OCPP Compatible

The current versions of the Zappi use Open Charge Point Protocol or OCPP for short. This is a standardized method for EVs and chargers to communicate and is useful because it makes it more likely it will be able to integrate with other energy management equipment you may wish to install in the future.

Charging Cable

You can get a Zappi with a 6.5m hardwired charging cable, which is longer than the 5m many EV chargers have.  You can also pay around $50 less and get one without a cable and just has a socket. This can be an useful if you need to use a cable longer than 6.5m.

Operating Temperature

Its operating temperature is from -25°C to 40°C. This temperature range is fine for the UK where it has only exceeded 40°C once - so far - but it’s not ideal for Australia where the temperature can go over 40°C in almost any location. The good news is - at the moment - its maximum operating temperature will only rarely be exceeded in most towns and cities.

EV chargers can derate and provide less power as they approach their maximum operating temperature and this could be an issue in Australian summers.

A Choice Of Boring Colours

Unlike the majority of EV chargers that only have one colour on their plastic case, Zappi EV chargers have two-tone cases. You can choose between black and grey or white and grey.

3 Year Warranty

The Zappi warranty is only for three years, which isn’t very long. However, many EV chargers only have two-year warranties, so it’s a little better than average.

No Australian Office

The manufacturer of the Zappi, myenergie, doesn't have an Australian office.  This makes the importer responsible for the warranty and for their obligations under Australian consumer law.  But if you buy a Zappi from myenergie in the UK and have it mailed to you, that makes you the importer.  This doesn't mean myenergie won't help you if there is a problem.  We know they have replaced units that have failed in Australia.  But if they decide not to help you, there may not be much you can do about it.

My recommendation is to buy an EV charger from an installer.  This makes them responsible for the and if there are any problems they have an obligation to fix them.  If your installer is no longer around then you can contact myenergie to make a warranty claim.

Price

At the time of writing in June 2024, a single-phase Zappi costs around $1,600 before installation. A 3-phase one is around $1,900. Getting one without a cable cuts the cost by around $50.

Installation adds a lot to the total cost. Three-phase chargers require more work and so are generally more to install. Setting up smart charging capability also requires additional labour. For these reasons, installation can easily cost $800 to $1,000 or more.

Recommendation

If you’re not interested in solar smart charging then the Zappi won’t be a cost-effective choice. But if you want an EV charger that can smart charge without requiring additional hardware, then the current versions of the Zappi EV charger are worth considering. But keep in mind how often your location goes above its maximum operating temperature of 40°C.